Static White LED Tapelight COB

The COB is built on a flexible chip-on-board (COB) circuit for a continuous, dot-free light line, backed with 3M adhesive for direct-surface mounting. It is offered in two constructions: an open-face IP20 format for protected interior channels and surfaces, and a silicone-jacketed, round-tube IP67 format with sealed end caps for wet-location and direct-exposure installations. Minimum channel width varies by power tier and IP rating — from 8mm (0.315") up to 16mm (0.630") — so the correct tier should be confirmed against the mounting channel or extrusion before ordering. Each reel runs up to 16 ft. 4 in. and is cut-to-length at pre-marked intervals specific to its power tier. The COB is UL, cUL, CE, and RoHS approved, backed by a five-year warranty, and rated for operation from -20°C to 60°C (-4°F to 140°F). 

The COB operates on 24V DC constant voltage input, compatible with SAGE-recommended constant voltage LED drivers. Available across three power tiers, the tape draws between 3.7 and 5.5 watts per foot depending on model, delivering between 305 and 518 lumens per foot at an efficacy of 94 to 100 lm/W. Color temperature is available in four static-white settings — 2700K, 3000K, 4000K, and 6500K — selected at the time of order rather than adjustable after installation. CRI is 90+, with a 170-degree distribution angle for broad, even wash lighting. 

Part of the Lynx Linear Lighting collection: The COB Static White LED Tapelight is part of the Lynx Linear Lighting portfolio from SAGE Brands, a division focused on flexible tape, neon flex, and linear lighting solutions for cove, accent, and architectural applications. Its connector accessories and driver compatibility are shared across the broader Lynx linear product line, simplifying specification when multiple linear runs are used on the same project.

Choosing between IP20 and IP67: The IP20 construction is designed for protected interior applications — cabinetry, coves, and channels where the tape is shielded from moisture and direct handling. The IP67 construction adds a sealed silicone jacket and end caps, making it suitable for wet locations, exterior architectural work, and any installation where washdown, humidity, or direct water exposure is a factor. Confirm the correct construction for the installation environment before ordering, as channel width requirements differ between the two.

Selecting a power tier: The COB-3, COB-4, and COB-5 tiers offer increasing output — from a lower-density option suited to subtle grazing and backlighting up to a higher-output tier for cove and signage applications where more lumens per foot are needed. The COB-5 delivers the highest output per foot but at a slightly reduced efficacy compared to COB-3 and COB-4, a normal trade-off at higher drive currents.

Choosing a color temperature: The COB is available in four static-white settings — 2700K and 3000K for warm, residential-feeling applications; 4000K for a neutral tone suited to commercial and retail environments; and 6500K for a cool, high-contrast white often used in signage and task-adjacent accent lighting. Because color temperature is fixed at the time of order, confirm the desired CCT against the project's other fixtures before placing the order.

Driver and dimming compatibility: The COB pairs with SAGE's recommended constant voltage drivers — the D-60W, D-96W, and D-300W, each offering 5-in-1 dimming compatibility, or the D-60W-ND for non-dimming applications. When sizing a driver, total the wattage per foot across the full run and select a driver with adequate headroom above that load; larger installations may require multiple drivers or runs.

Ordering logic: Use the format COB-[Power]-[CCT]-[IP Rating]-[Length], for example COB-3-27-IP20-ST, which specifies the 3.7W/ft tier in 2700K, IP20 construction, at standard 16 ft. 4 in. cut-in-field length. Connector accessories are ordered separately using the format CN-[Accessory Code], such as CN-BTCB8 for a board-to-board connector with cable, and should be specified based on the number of splices, corners, and power feed points required for the run.